[profile]
layer_height = 0.2
wall_thickness = 1.0
retraction_enable = True
solid_layer_thickness = 0.8
fill_density = 20
nozzle_size = 0.5
print_speed = 40
print_temperature = 195
print_temperature2 = 185.0
print_temperature3 = 0
print_temperature4 = 0
print_bed_temperature = 50
print_remove_temperature = 0
support = None
platform_adhesion = Raft
support_dual_extrusion = Second extruder
wipe_tower = True
wipe_tower_volume = 30
ooze_shield = False
filament_diameter = 1.75
filament_diameter2 = 1.75
filament_diameter3 = 0
filament_diameter4 = 0
filament_flow = 100
retraction_speed = 40
retraction_amount = 1.5
retraction_dual_amount = 4.5
retraction_min_travel = 1.5
retraction_combing = True
retraction_minimal_extrusion = 0.02
retraction_hop = 0
bottom_thickness = 0.0
layer0_width_factor = 100
object_sink = 0.0
overlap_dual = 0.15
travel_speed = 60
bottom_layer_speed = 20
infill_speed = 38
inset0_speed = 25
insetx_speed = 30
z_offset = 0
z_offset_left = 0
z_offset_right = 0
ext_steps = 0
cool_min_layer_time = 12
fan_enabled = True
skirt_line_count = 2
skirt_gap = 2.0
skirt_minimal_length = 150.0
fan_full_height = 0.6
fan_speed = 100
fan_speed_max = 100
cool_min_feedrate = 10
cool_head_lift = True
solid_top = True
solid_bottom = True
fill_overlap = 15
support_type = Lines
support_angle = 50
support_fill_rate = 15
support_xy_distance = 1.2
support_z_distance = 0.2
spiralize = False
simple_mode = False
brim_line_count = 20
raft_margin = 5.0
raft_line_spacing = 3.0
raft_base_thickness = 0.3
raft_base_linewidth = 1.0
raft_interface_thickness = 0.27
raft_interface_linewidth = 0.4
raft_airgap = 0.22
raft_surface_layers = 2
fix_horrible_union_all_type_a = True
fix_horrible_union_all_type_b = False
fix_horrible_use_open_bits = False
fix_horrible_extensive_stitching = False
plugin_config = 
object_center_x = -1
object_center_y = -1
server_ip = kloner3d.local
server_api = kloner3d
server_port = 80
server_user = KLONER3D
server_password = kloner3d
server_ssl = False
head_diameter1 = 175
head_diameter2 = 175
twin_mode = no
arm_mode = left
twin_nozzle_1 = 0.5
twin_nozzle_2 = 0.5
normal_nozzle = 0.5
twin_port_left = 
twin_port_right = 

[alterations]
start.gcode = 
	;Sliced at: {day} {date} {time}
	;Basic settings: Layer height: {layer_height}
	;Basic settings: Walls: {wall_thickness}
	;Basic settings: Fill: {fill_density}
	;Print time: {print_time}
	;Filament used: {filament_amount}m {filament_weight}g
	M140 S{print_bed_temperature}
	M42 P22 S0
	G21
	G90
	M107
	G28 Z
	G28 X Y
	G1 X143 Y0 F5000
	G1 Z-0.5 F2000
	G1 Z0 F2000
	G1 F500
	;***********************************************
	;***          Z OFFSET COMPENSATION          ***
	;***********************************************
	G1 Z0
	;***********************************************
	;***********************************************
	G92 Z0
	M109 T0 S{print_temperature}
	G92 E-35
	G1 E-0.1 F80
	G1 E-0.3
	G92 E0
	G1 Z{layer_height}
	G1 F{travel_speed}
end.gcode = 
	G1 X0 F4000
	G28 Z
	G28 X Y
	M107
	M104 S0
	M140 S0
	G92 E0
	G1 E-2 F50
	M140 S{print_remove_temperature}
	;{profile_string}
start2.gcode = 
	;Sliced at: {day} {date} {time}
	;Basic settings: Layer height: {layer_height}
	;Basic settings: Walls: {wall_thickness}
	;Basic settings: Fill: {fill_density}
	;Print time: {print_time}
	;Filament used: {filament_amount}m {filament_weight}g
	M140 S{print_bed_temperature}
	T0
	M104 S{print_temperature}
	T1
	M104 S{print_temperature2}
	M42 P22 S0
	G21
	G90
	M107
	G28 Z
	G28 X Y
	G92 Y215
	G1 X0 Y8.5 F5000
	G1 Z-0.5 F2000
	G1 F500
	;***********************************************
	;***          Z OFFSET COMPENSATION          ***
	;***********************************************
	G1 Z{z_offset}
	;***********************************************
	;***********************************************
	G92 Z0
	T0
	M109 S{print_temperature}
	G92 E-35
	G1 E-0.1 F80
	G1 E-0.3
	G92 E0
	T1
	M109 S{print_temperature2}
	G92 E-35
	G1 E-0.1 F80
	G1 E-0.3
	G92 E0
	T0
	G1 Z{layer_height}
	G1 X10 F2000
	G1 F{travel_speed}
end2.gcode = 
	G1 X0 F4000
	G28 Z
	G28 X Y
	M107
	T0
	M104 S0
	T1
	M104 S0
	M140 S0
	T0
	G92 E0
	G1 E-2 F50
	T1
	G92 E0
	G1 E-2 F50
	M140 S{print_remove_temperature}
	;{profile_string}
start3.gcode = ;Sliced at: {day} {date} {time}
	;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
	;Print time: {print_time}
	;Filament used: {filament_amount}m {filament_weight}g
	;Filament cost: {filament_cost}
	;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
	;M104 S{print_temperature} ;Uncomment to add your own temperature line
	;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
	;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
	G21        ;metric values
	G90        ;absolute positioning
	M107       ;start with the fan off
	G28 X0 Y0  ;move X/Y to min endstops
	G28 Z0     ;move Z to min endstops
	G1 Z15.0 F{travel_speed} ;move the platform down 15mm
	T2                      ;Switch to the 2nd extruder
	G92 E0                  ;zero the extruded length
	G1 F200 E10             ;extrude 10mm of feed stock
	G92 E0                  ;zero the extruded length again
	G1 F200 E-{retraction_dual_amount}
	T1                      ;Switch to the 2nd extruder
	G92 E0                  ;zero the extruded length
	G1 F200 E10             ;extrude 10mm of feed stock
	G92 E0                  ;zero the extruded length again
	G1 F200 E-{retraction_dual_amount}
	T0                      ;Switch to the first extruder
	G92 E0                  ;zero the extruded length
	G1 F200 E10             ;extrude 10mm of feed stock
	G92 E0                  ;zero the extruded length again
	G1 F{travel_speed}
	;Put printing message on LCD screen
	M117 Printing...
end3.gcode = ;End GCode
	M104 T0 S0                     ;extruder heater off
	M104 T1 S0                     ;extruder heater off
	M104 T2 S0                     ;extruder heater off
	M140 S0                     ;heated bed heater off (if you have it)
	G91                                    ;relative positioning
	G1 E-1 F300                            ;retract the filament a bit before lifting the nozzle, to release some of the pressure
	G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
	G28 X0 Y0                              ;move X/Y to min endstops, so the head is out of the way
	M84                         ;steppers off
	G90                         ;absolute positioning
	;{profile_string}
start4.gcode = ;Sliced at: {day} {date} {time}
	;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
	;Print time: {print_time}
	;Filament used: {filament_amount}m {filament_weight}g
	;Filament cost: {filament_cost}
	;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
	;M104 S{print_temperature} ;Uncomment to add your own temperature line
	;M109 T2 S{print_temperature2} ;Uncomment to add your own temperature line
	;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
	;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
	G21        ;metric values
	G90        ;absolute positioning
	M107       ;start with the fan off
	G28 X0 Y0  ;move X/Y to min endstops
	G28 Z0     ;move Z to min endstops
	G1 Z15.0 F{travel_speed} ;move the platform down 15mm
	T3                      ;Switch to the 4th extruder
	G92 E0                  ;zero the extruded length
	G1 F200 E10             ;extrude 10mm of feed stock
	G92 E0                  ;zero the extruded length again
	G1 F200 E-{retraction_dual_amount}
	T2                      ;Switch to the 3th extruder
	G92 E0                  ;zero the extruded length
	G1 F200 E10             ;extrude 10mm of feed stock
	G92 E0                  ;zero the extruded length again
	G1 F200 E-{retraction_dual_amount}
	T1                      ;Switch to the 2nd extruder
	G92 E0                  ;zero the extruded length
	G1 F200 E10             ;extrude 10mm of feed stock
	G92 E0                  ;zero the extruded length again
	G1 F200 E-{retraction_dual_amount}
	T0                      ;Switch to the first extruder
	G92 E0                  ;zero the extruded length
	G1 F200 E10             ;extrude 10mm of feed stock
	G92 E0                  ;zero the extruded length again
	G1 F{travel_speed}
	;Put printing message on LCD screen
	M117 Printing...
end4.gcode = ;End GCode
	M104 T0 S0                     ;extruder heater off
	M104 T1 S0                     ;extruder heater off
	M104 T2 S0                     ;extruder heater off
	M104 T3 S0                     ;extruder heater off
	M140 S0                     ;heated bed heater off (if you have it)
	G91                                    ;relative positioning
	G1 E-1 F300                            ;retract the filament a bit before lifting the nozzle, to release some of the pressure
	G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
	G28 X0 Y0                              ;move X/Y to min endstops, so the head is out of the way
	M84                         ;steppers off
	G90                         ;absolute positioning
	;{profile_string}
start_twin.gcode = 
	;Sliced at: {day} {date} {time}
	;Basic settings: Layer height: {layer_height}
	;Basic settings: Walls: {wall_thickness}
	;Basic settings: Fill: {fill_density}
	;Print time: {print_time}
	;Filament used: {filament_amount}m {filament_weight}g
	M140 S{print_bed_temperature}
	M104 S{print_temperature}
	M42 P22 S0
	G21
	G90
	M107
	G28 Z
	G28 X Y
	G1 Y0 F5000
	G1 Z-0.5 F2000
	G1 F500
	;***********************************************
	;***          Z OFFSET COMPENSATION          ***
	;***********************************************
	G1 Z{z_offset_left}
	;***********************************************
	;***********************************************
	G92 Z0
	G1 Z{layer_height}
	M109 T0 S{print_temperature}
	G92 E-35
	G1 E-0.1 F80
	G1 E-0.3
	G92 E0
	G1 X20 F2000
	G1 F{travel_speed}
end_twin.gcode = 
	G1 X0 F4000
	G28 Z
	G28 X Y
	M107
	M104 S0
	M140 S0
	G92 E0
	G1 E-2 F50
	M140 S{print_remove_temperature}
	;{profile_string}
start_combo.gcode = 
	;Sliced at: {day} {date} {time}
	;Basic settings: Layer height: {layer_height}
	;Basic settings: Walls: {wall_thickness}
	;Basic settings: Fill: {fill_density}
	;Print time: {print_time}
	;Filament used: {filament_amount}m {filament_weight}g
	M77
	T0
	M140 S{print_bed_temperature}
	M104 S{print_temperature}
	M42 P22 S0
	G21
	G90
	M107
	T1
	M140 S{print_bed_temperature}
	M104 S{print_temperature}
	M42 P22 S0
	G21
	G90
	M107
	T0
	G28 Z
	T1
	G28 Z
	T0
	G28 X Y
	T1
	G28 X Y
	T0
	G1 Y0 F5000
	G1 Z-0.5 F2000
	G1 F500
	;***********************************************
	;***          Z OFFSET COMPENSATION          ***
	;***********************************************
	G1 Z{z_offset_left}
	;***********************************************
	;***********************************************
	G92 Z0
	G1 Z{layer_height}
	G1 F{travel_speed}
	T1
	G1 Y0 F5000
	G1 Z-0.5 F2000
	G1 F500
	;***********************************************
	;***          Z OFFSET COMPENSATION          ***
	;***********************************************
	G1 Z{z_offset_right}
	;***********************************************
	;***********************************************
	G92 Z0
	G1 Z{layer_height}
	T0
	M109 T0 S{print_temperature}
	T1
	M109 T0 S{print_temperature2}
	T0
	G92 E-35
	G1 E-0.1 F80
	G1 E-0.3
	G92 E0
	T1
	G92 E-35
	G1 E-0.1 F80
	G1 E-0.3
	G92 E0
	G1 F{travel_speed}
	T0
	G1 F{travel_speed}
end_combo.gcode = 
	M78
	M107
	;{profile_string}
support_start.gcode = 
support_end.gcode = 
cool_start.gcode = 
cool_end.gcode = 
replace.csv = 
preswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
	;This code is added before the T(n)
postswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
	;This code is added after the T(n)